TG6™
Perfect Dental (Shenzhen Perfect Medical Instruments)
TG6™
Perfect Dental (Shenzhen Perfect Medical Instruments)
Eight-instrument sequence with V0/V1/V2 glide-path openers and T1–T5 shapers spanning 18/.02 through 50/.05 at 250–350 rpm (per IFU spec table)
Continuous Rotation · NiTi
- RPM
- Ncm1.5–3
- File
- 8
- Verified
Specifications
Tap icons for term definitions
| File | Tip | Taper | SpeedRPM | TorqueNcm | Role |
|---|---|---|---|---|---|
Diameter at the file tip (D0). Larger tips shape wider canals. | |||||
How much the file widens per mm. Higher taper = more aggressive cutting. | |||||
Rotational speed (RPM). Follow manufacturer settings to prevent file breakage. | |||||
Rotational force limit (Ncm). Prevents file fracture by auto-reversing when resistance is too high. | |||||
V0 19/.04 | 0.19 | 4% | 250-350 | 3.0 | Orifice opener |
V1 18/.02 | 0.18 | 2% | 250-350 | 3.0 | Glide path |
V2 20/.04yellow | 0.20 | 4% | 250-350 | 1.5 | Shaping |
T1 20/.07yellow | 0.20 | 7% | 250-350 | 1.5 | Shaping |
T2 25/.08red | 0.25 | 8% | 250-350 | 2.5 | Shaping |
T3 30/.09blue | 0.30 | 9% | 250-350 | 2.5 | Shaping |
T4 40/.06black | 0.40 | 6% | 250-350 | 2.5 | Finishing |
T5 50/.05yellow | 0.50 | 5% | 250-350 | 2.5 | Finishing |
Clinical Tips
- TG6 is an 8-instrument sequence (per IFU spec table): V0 19/.04 (optional orifice opener, 19 mm), V1 18/.02 (glide path), V2 20/.04 and T1 20/.07 (primary shapers used together per IFU step 6), T2 25/.08 / T3 30/.09 / T4 40/.06 / T5 50/.05 (escalation files used sequentially only if the ISO 020 K-file gauge is loose per IFU step 7)
- K-file gauge with ISO 020 between primary shaping (V2+T1) and any escalation is required per IFU step 7
- T3 30/.09 is the largest taper in the set — verify motor torque headroom before use (general guidance)
- Cross-section geometry is not specified by name in the IFU text
Warnings
- Single-use; discard after each canal (per IFU section 3)
- Do not autoclave above 200 °C including drying phase (per IFU precautions)
- Do not fully immerse in NaOCl; only the working part may contact a max 5% NaOCl solution for up to 5 minutes (per IFU section 4)
- Inspect each file for distortion, unwinding, corrosion, or damaged edges before use (per IFU section 4)
- Use minimal apical pressure; never force the file (per IFU section 4)
- Contraindicated in patients with nickel allergy (per IFU section 1)
Obturation Techniques
Single cone, warm vertical, carrier-based & lateral compaction
Protocol
01Glide Path3
02Shaping3
03Finishing1
Related Systems
From Perfect Dental Systems
Manufacturer page
Perfect Dental SystemsOther continuous rotation systems
Motion category
Continuous RotationAlloy
Conventional NiTiCollections
Clinical guides
Frequently Asked Questions
What alloy is TG6 made from?
What alloy is TG6 made from?
Answer
TG6™ is manufactured from NiTi with conventional heat treatment.
How many files are in the TG6 sequence?
How many files are in the TG6 sequence?
Answer
The TG6™ system includes 8 files: V0 19/.04, V1 18/.02, V2 20/.04, T1 20/.07, T2 25/.08, T3 30/.09, T4 40/.06, T5 50/.05.
What is the TG6 file sequence?
What is the TG6 file sequence?
Answer
TG6™ is used in this order: V0 19/.04 → V1 18/.02 → V2 20/.04 → T1 20/.07 → T2 25/.08 → T3 30/.09 → T4 40/.06 → T5 50/.05.
- Per-file speed, torque and technique are in the protocol section above.
What motion type does TG6 use?
What motion type does TG6 use?
Answer
TG6™ uses continuous rotation motion.
What cases is TG6 best for?
What cases is TG6 best for?
Answer
TG6™ is best suited for: extended sequence with built-in K-file gauge checks, wider canals where T4/T5 finishing matters, practices wanting a single-brand glide path through finishing.
What speed and torque settings are recommended for TG6?
What speed and torque settings are recommended for TG6?
Answer
Recommended settings: 250-350 RPM and 3.0 / 1.5 / 2.5 Ncm across the file sequence (refer to official DFU for full per-file parameters).
Reviewed by
Uzm. Dt. Levent Yüksel
DDS · Endodontist
Endodontist — DDS, Hacettepe University; endodontics specialty training, Ankara University. 10+ years of clinical experience. Sole author and reviewer of EndoGuide content.
Cite this page
Citation formats for the manufacturer-verified specification data on this page.
AMA
Yüksel L. TG6: sequence, speed and torque settings. EndoGuide. Updated: 2026-11-12. https://endo-guide.app/system/perfect-tg6
BibTeX
@misc{endoguide-perfect-tg6,
author = {Yüksel, Levent},
title = {TG6: sequence, speed and torque settings},
howpublished = {\url{https://endo-guide.app/system/perfect-tg6}},
year = {2026},
note = {EndoGuide. Updated: 2026-11-12}
}Powered by:Uzm. Dt. Levent Yüksel
@endoguideappIndependent educational resource. Product names and trademarks belong to their respective manufacturers, who neither sponsor nor endorse EndoGuide.